RB Bouwchemie · Almelo

Sealing, insulating andprotecting.

Basement waterproofing, damp-proofing, water management and thermal coatings. We provide advice, supply products and oversee or carry out the work.

RB Bouwchemie on site, with images of injection work, basement waterproofing and floor coating
Personal contactTailored adviceProducts and applicationFor new builds and renovation
Our solutions

A good building starts
with the right protection.

Damp, leaks or a cold wall? We look at the root cause and tailor our approach to your situation.

Basement waterproofing in progress
01 / SEALING

Basement waterproofing

A wet basement requires more than simply treating visible patches. We assess where the water is entering and advise on a suitable waterproofing system for walls, floors and junctions.

For concrete and masonry, in both existing buildings and new builds. The choice between internal or external waterproofing depends on the structure and accessibility.

Discuss your basement problem
Illustrative comparison of a wall with and without thermal coating
02 / COATING

Thermal coatings

A complementary approach for specific structural challenges. We advise on thermal coatings and assess which system best suits the substrate, the application and your goals.

From product selection and supply to guidance and application: one point of contact for the entire process.

Explore the possibilities
03 / INSULATION

Thermal insulation

Struggling with cold bridges, cold interior walls or condensation? We assess the situation and advise where a thermal coating from Alpha Czech can help.

04 / DAMP-PROOFING

Rising damp

Damp patches, salt deposits or flaking plaster? We investigate the source of the moisture and determine which treatment and finish is right for your walls.

05 / WATERPROOFING

Swimming pool waterproofing

A carefully constructed waterproofing system for new and existing swimming pools, with close attention to the substrate, penetrations and junctions.


06 / JUNCTIONS

Airtightness

Careful attention to joints, seams and connections in the building envelope. We assist with suitable materials and thorough airtightness detailing.

07 / INJECTION

Injection

Targeted sealing of cracks, joints and leaks using injection techniques.

Materials and systems

Brands we work with

We work with HEYEN Bauchemie GmbH, ALPHA CZECH, Volteco and SPETEC®.

RB Bouwchemie B.V. is the official distributor for the entire Benelux of all ALPHA CZECH products.

Thermally insulating coating

What is a thermally insulating coating?

A thin, liquid-applied finish coat for a suitable substrate, such as a wall, roof or pipe. Once dry, the coating forms a solid layer.

What does a thermal coating do?

A thermal coating forms a thin layer designed to reflect and retain heat radiation, creating a comfortable indoor climate. Suitable for interior and exterior use, and effective against cold bridges, condensation and mould growth. For example, a suitable roof coating can limit solar heat gain. For condensation on cold installations, specific coatings are available. The effect depends on the product, layer thickness and conditions.

What could it mean for my project?

If you have a roof that overheats or a cold pipe with condensation, a suitable coating may be part of the solution. We assess the substrate, the cause and the desired outcome. Where a specific insulation value is required, we consider the full construction.

Application examples

Thermal coatings

A thin layer.
A well-considered choice.

Want to know whether a thermal coating is suitable for your wall, façade or roof? It starts with a clear objective and an assessment of the existing situation.

Book a consultation

RB Bouwchemie B.V. is the official distributor for the entire Benelux of all ALPHA CZECH products.

  • 01 — The right application
    We discuss the substrate, moisture load, conditions of use and desired finish.
  • 02 — Well-founded product advice
    We assess the technical product data and available test results for your application.
  • 03 — Guidance and application
    From preparation and product delivery to on-site guidance or full execution.

Performance depends on the product chosen, the layer thickness and the conditions. A thermal coating does not straightforwardly replace conventional insulation. Where condensation is an issue, we also look at ventilation, humidity and surface temperature.

Advice · Sales · Guidance · Application
View all product data sheets ↓
ALPHA CZECH · Drying & curing

Give the coating time to do its job.

A thermal coating from ALPHA CZECH requires sufficient drying time to achieve its intended properties. Touch-dry does not mean the entire layer is dry and ready for use. Always follow the technical data sheet for the chosen system.

Why is drying essential?

According to the manufacturer, these coatings combine reflective properties with hollow microspheres. During drying, water evaporates from the coating and the final layer is formed. A layer that is too thick may remain moist on the inside and adversely affect performance. The correct layer thickness, drying time and application conditions are therefore essential.

Drying times per product

The following guidelines apply at 20 °C and 60% relative humidity, for a single coat at the prescribed standard thickness.

Guidelines from the ALPHA CZECH technical data sheets
ProductTouch-dryNext coatAfter 24 hours
ALPHA TOP
Approx. 30 minutes
After 6 hours
Fully dry and functional according to the data sheet.
ALPHA TEMPER
Approx. 3 hours
After 12 hours
Resistant to damage from washing off the paint layer, according to the data sheet.

Allow for conditions.Low temperatures and high humidity will extend drying time. The time to full drying also depends on layer thickness and substrate. Ensure adequate ventilation and follow the instructions for each coat.

Application on hot surfaces

According to the manufacturer, ALPHA TEMPER can be applied to surfaces of up to +220 °C using a specific method. This is a product-specific application that requires appropriate preparation and build-up of coats. This temperature does not apply to all ALPHA coatings: the data sheet for ALPHA TOP states an application temperature of +5 to +35 °C.

Thermal coatings in pictures

See the applications.

From roof to interior wall: these illustrations provide a clear view of the various situations.

Illustrative comparison of a roof with and without thermal coating.

Thermal roof coating

Illustrative comparison of a roof with and without thermal coating.

Illustrative comparison at an internal corner and window.

Cold bridge on the interior side

Illustrative comparison at an internal corner and window.

Schematic explanation of wall temperature and dew point.

Basement wall and condensation

Schematic explanation of wall temperature and dew point.

Illustrative representation on a thermal imaging camera.

Thermal wall coating

Illustrative representation on a thermal imaging camera.

The thermal images are schematic illustrations, not actual measurements or proof of product performance. The suitability and effect of a coating are assessed on a case-by-case basis.

Photos from practice

Damp-proofing and basement waterproofing.

A look at the preparation, injection work and application. Careful attention to the substrate and the junctions forms the foundation of the approach.

Exposed wall base and substrate during the works.

Preparing the brickwork

Exposed wall base and substrate during the works.

HEYEN Horizontalstop with injection equipment on site.

Materials and equipment

HEYEN Horizontalstop with injection equipment on site.

Injection points in the brickwork during treatment against rising damp.

Injection works

Injection points in the brickwork during treatment against rising damp.

Application to the basement wall during execution.

Applying the coating

Application to the basement wall during execution.

Work on the junction between the basement floor and wall.

Attention to junctions

Work on the junction between the basement floor and wall.

Get to know RB Bouwchemie

Our expertise.
In half a minute.

Watch our short introduction to basement waterproofing and protecting your building.

Introduction film RB Bouwchemie · 31 seconds · with sound

Swimming pool waterproofing

Attention to the entire pool.

A real-life image of a swimming pool under construction, showing the walls, floor, steps and pipe penetrations.

Swimming pool under construction with steps, wall penetrations and junctions

Swimming pool under construction

Overview of the pool and connection details during construction.

Sealing & injection

Targeted treatment of
cracks and leaks.

On-site images of injection work on a concrete wall. Get a close-up view of the equipment, the crack, and the application process.

Injection pump with pressure gauge during work on a concrete wall.

Injection equipment

Injection pump with pressure gauge during work on a concrete wall.

Detail of the crack and the connection point for injection.

The crack in detail

Detail of the crack and the connection point for injection.

Overview of the pump and injection hose connected to the concrete wall.

Injecting the concrete wall

Overview of the pump and injection hose connected to the concrete wall.

Overview of the concrete wall at the work site.

Concrete wall on location

Overview of the concrete wall at the work site.

Injection in action

Injection demo

Get a close-up look at the injection equipment and the injection process on a masonry test setup.

Injection demo · 57 seconds · no audio

ALPHA CZECH · Downloads

The right product.
The technical details.

Download the ALPHA CZECH technical data sheets for information on application, substrate preparation, and processing.

Volteco

ALPHA CZECH product data sheets – Thermally insulating coating

VoltecoVolteco product data sheets and brochures – Waterproofing and protective solutions

47 Dutch-language technical data sheets for sealing and protection.

VoltecoDutch-language brochures and catalogue

HEYEN BauchemieHeyen Bauchemie product sheets – waterproofing products

Download the complete bundle ↗

Our approach

Understand first.
Then solve it properly.

01

Your question

You tell us what's going on and share photos of the situation where possible.

02

Assessment

We discuss the cause, the substrate, and whether an on-site assessment is needed.

03

A clear proposal

You receive a suitable approach and clear agreements on the work to be carried out and the costs involved.

04

Getting started

We supply the products, support the application, or handle the work ourselves – as agreed.

Good to know

Your questions.
Answered clearly.

What is the difference between a leak and condensation?

With a leak, water enters through an opening or through the structure itself. Condensation occurs when moist air cools on a cold surface. Both require a different approach, which is why we always assess the cause first.

Can a basement be waterproofed from the inside?

In many situations, yes. Whether it is appropriate depends on factors such as the structure, water pressure, substrate, and connections. We assess this before recommending a system.

Is a thermal coating suitable for my building?

That depends on your goal and the technical properties of the specific product. We discuss your situation and the available product data, so you can make an informed judgement about what to expect from the application.

Can I order products only?

Yes. You can come to RB Bouwchemie for products and advice. Support with application and installation is also available. Get in touch to discuss your project and product selection.

Let's get acquainted

What can we do for
your building?

Tell us what you're up against. With a brief description and a few photos, we can discuss your question in a focused and meaningful way.

RB Bouwchemie B.V.
Slot 10 · 7608 ND Almelo

Ask RBbouwchemie

Choose a frequently asked question. For advice on your own project, we're happy to help you personally.

Which Alpha Czech products does RBbouwchemie supply?

RBbouwchemie is the official distributor of the full Alpha Czech range in the Netherlands, Belgium, and Luxembourg.

View the product sheets
Can a thermal coating help with condensation or cold bridges?

That depends on the situation. For tailored advice, we look at factors such as the substrate, ventilation, humidity, and surface temperature. Describe where and when the problem occurs.

Request project advice
Can I get advice about a damp or leaking basement?

Yes. Let us know whether the moisture is visible on the wall, the floor, or the junction between the two, and when it occurs. Photos will help us discuss your question more precisely.

Discuss your basement
Can I request a quote or order a product?

Yes. Choose Quote for a project enquiry, or Product Sales for pricing and availability of materials. If known, please include the required quantity or surface area.

Start your request
Send your question to RBbouwchemie

Email assistant

Compose an email to RBbouwchemie in a few simple steps.

Drag files here or browse files
Max. 3 files, 2 MB per file (images, PDF, Word, Excel)